066-095-PAE

This is a replacement kit for the GE multi-section can capacitors used inside the McIntosh MC2100, MC2105, and MC2300 power amplifiers. These cans were stamped with McIntosh part number 066-095. Other models may also use this can. High quality, genuine Nichicon capacitors rated for operation up to 105°C are used to ensure a long operational lifespan, and a custom PCB with thick 2 oz. copper provides a robust and elegant mounting solution. Four wiring turrets facilitate the connections to each of the four caps. No more gutting the old cans and sticking new caps inside!

Includes four Nichicon capacitors, one cap mounting PCB, one spacer PCB, a hardware kit, and a thorough step-by-step installation guide.

Installing this kit will require soldering, drilling out the original can’s mounting rivets, and stripping/attaching wires in a tight space. If you do not have prior experience safely testing and repairing amplifiers at the component level, please have a qualified professional install this kit in your unit.

The following capacitor values are included:

• 82uF 200V (Replaces 80uF 200V)
• 82uF 200V (Replaces 80uF 200V)
• 150uF 160V (Replaces 150uF 150V)
• 56uF 160V (Replaces 50uF 150V)

Note: The capacitor symbols (square, triangle, half-circle, dash) on the cap PCB were arranged based on the orientation of the original can in the MC2300. Other models, such as the MC2100, typically had the cans oriented differently, meaning the position of the symbols on this board may not align with your original installation.

128-165-PAE

This is a new-production input preamp board for the McIntosh MC2100, MC2105, and MC2300 power amplifiers. This board follows the original component layout closely, and no changes were made to the original circuit design.

The new PCB is double-sided and is manufactured with plated through-holes and a gold finish. Silkscreen reference designators and symbols are provided on both sides. Robust wiring turrets replace the original hollow posts that cables solder to. All component footprints are sized to fit the original parts. In addition, all axial electrolytic capacitors have footprints for radial parts of various sizes, both input film caps support two different lead spacings, and both electrolytic output caps can be substituted with film caps of the appropriate physical size. A capacitor sizing guide is included with unpopulated kits.

Assembled boards are built using high quality components, including Vishay MRS25 series low noise metal film resistors (1% tolerance, 600 mW, 50 ppm TCR), Nichicon electrolytic capacitors (UPM series for supply filters, UKZ for audio stages), WIMA film capacitors, and new transistors. All assembled boards are burn-in tested for 24 hours and run through an Audio Precision analyzer to confirm that they meet the performance specifications listed below.

Parts Included (Assembled Board)

• Assembled and tested MC2100/2105/2300 input preamp board
• Anti-static bag for storing your original input board
• Two 22 kOhm resistors for MC2300’s below S/N 4Y426
• Installation guide with redrawn schematic, board layout, and parts list

Parts Included (Unpopulated PCB)

• Unpopulated MC2100/2105/2300 input preamp PCB
• 16 wiring turrets (one extra)
• Anti-static bag for storing your original input board
• Resistor lead forming tool
• Installation guide with redrawn schematic, board layout, and parts list

Typical Performance

Typical performance of both channels (Audio Precision analyzer, 2 Vrms output from DUT):

• Gain: 20.83 dB @ 1 kHz
• Frequency response: +0.01 dB, -0.25 dB from 20 Hz to 20 KHz
• Signal to noise ratio: -97.1 dB below 2 V output (20 Hz – 22 KHz analyzer fltr, unwtd)
• THD+N: Less than 0.007% from 20 Hz – 20 KHz (no analyzer fltr, unwtd)
• IMD: Less than 0.005% (DIN 250 Hz/8 KHz 4:1)

Note that these specifications apply to the preamp board by itself and do not reflect the overall performance of your McIntosh amplifier. We have tested an original MC2100 input board in the same manner and found that this new board slightly exceeds the performance of the original.

We recommend testing your unit first to ensure it is working properly. If you are repairing your unit, please make sure your symptoms are originating from the preamp board before you replace it. Replacing this board will not resolve problems present in the rest of the unit, such as the power supply or amplifier sections. If you have not replaced the original multi-section can capacitor in your unit’s power supply, we recommend doing so; we offer a replacement capacitor kit with a custom designed PCB for this task.

Please do not attempt to install these boards if you are not thoroughly familiar with safely diagnosing, repairing, and testing amplifiers at the component level with test equipment (signal generator, oscilloscope, load, etc.) and a current-limited power supply.